GANTER Grilli

?* Informazioni su tempi di consegna e prezzi

• • In Offerta fino al 30/06/2026

  

  Lifting points for welding

  GANTER

  Lifting points GN 589 are distinguished for their very low dimensions. They provide high dynamic and static strength and can be load from any direction with approved safety (safety factor 4) for all loading directions.
  The rated load carrying capacity listed in the above table is clearly marked on the lifting point. It applies to the most unfavourable load application of the load types listed opposite.
  Lifting points GN 589 comply with Mechanical Engineering Directive 2006 / 42 / EG.

  • Sconto volumi elevati

  Dati CAD disponibili in formato 2D / 3D

  A partire da∗ ：	56.78 €
  	Prezzo speciale
  Consegna da ：	Stesso giorno

  *Prezzo unitario in configurazione base

• 

  Load rings

  GANTER

  Load rings GN 5860 rotate running in ball bearings. The freely rotating ring allows the bolts to hold loads in any tensile direction.
  The rated load-bearing capacity is shown clearly on the load ring. It is valid for the most unfavourable case in terms of the types of load listed opposite. Load rings GN 5860 comply with Machine Engineering Directive 2006 / 42 / EG and are BG tested.
  The integrated RFID transponder clearly marks and identifies the sling and lifting gear, e.g. during the prescribed regular inspection.

  • Sconto volumi elevati

  Dati CAD disponibili in formato 2D / 3D

  A partire da∗ ：	179.38 €
  Consegna da ：	7 giorni

  *Prezzo unitario in configurazione base

• 

  Load rings (rotating), Steel

  GANTER

  The load rings GN 586 can be folded and rotated into all directions, carrying the full load in any tension direction.
  They offer a high load carrying capacity and they are tested to meet safety standards (safety factor 4).
  The rated load carrying capacity listed in the above table is clearly marked on the attachment bolt. It applies to the most unfavourable load application of the load types listed opposite.
  Load rings GN 586 comply with Mechanical Engineering Directive 2006 / 42 / EG and are BG tested.
  The integrated RFID transponder clearly marks and identifies the sling and lifting gear, e.g. during the prescribed regular inspection.

  • Sconto volumi elevati

  Dati CAD disponibili in formato 2D / 3D

  A partire da∗ ：	164.60 €
  Consegna da ：	7 giorni

  *Prezzo unitario in configurazione base

• • In Offerta fino al 30/06/2026

  

  Shackles, cranked

  GANTER

  High-strength, cranked shackles GN 585 are made in analogy with the US Federal Specification RR-C-271 and feature sixfold safety standards, which means that the minimum failure load is at least six times greater than the value of the nominal load (WLL). The cranked shape is particularly suitable for applications where the shackles are exposed to multiple loads.
  The rated size and the nominal load (WLL) are drop-forged into the shackle which makes it easier to select the proper sling gear. In general, the nominal load must not be exceeded.
  The designs with nut and split pin (Type B) are normally recommended for permanent connections. The bolts are allowed to rotate, and the nuts are secured against inadvertent loosening with a split pin.
  Operating instructions with more details and specifications are included with every delivery (see also www.ganter-griff.com/service).

  • Sconto volumi elevati

  Dati CAD disponibili in formato 2D / 3D

  A partire da∗ ：	3.10 €
  	Prezzo speciale
  Consegna da ：	Stesso giorno

  *Prezzo unitario in configurazione base

• • In Offerta fino al 30/06/2026

  

  Shackles, straight

  GANTER

  High-strength, straight shackles GN 584 are made in analogy with the US Federal Specification RR-C-271 and feature sixfold safety standards, which means that the minimum failure load is at least six times greater than the value of the nominal load (WLL).
  The rated size and the nominal load (WLL) are drop-forged into the shackle which makes it easier to select the proper sling gear. In general, the nominal load must not be exceeded.
  The designs with nut and split pin (Type B) are normally recommended for permanent connections. The bolts are allowed to rotate, and the nuts are secured against inadvertent loosening with a split pin.
  Operating instructions with more details and specifications are included with every delivery (see also www.ganter-griff.com/service).

  • Sconto volumi elevati

  Dati CAD disponibili in formato 2D / 3D

  A partire da∗ ：	3.20 €
  	Prezzo speciale
  Consegna da ：	Stesso giorno

  *Prezzo unitario in configurazione base

• 

  Golfare a gancio (GN 5862)

  GANTER

  I golfare a gancio GN 5862 ruotando si inseriscono nei cuscinetti a sfere. Il golfare a rotazione libera consente ai bulloni di sostenere i carichi in qualsiasi direzione di trazione consentita.
  
  La capacità portante nominale elencata nella tabella è indicata chiaramente sulla sede del cuscinetto. È relativa all'applicazione di carico più sfavorevole dei tipi di carico elencati qui accanto.
  
  I golfare a gancio GN 5862 sono conformi alla Direttiva macchine 2006 / 42 / EG e testati BG.
  
  L’integrato transponder RFID serve a contrassegnare e a facilitare l’identificazione dell'imbracatura e dell'ingranaggio di sollevamento, ad es. in occasione della prescritta verifica periodica.

  • Sconto volumi elevati

  A partire da∗ ：	258.98 €
  Consegna da ：	7 giorni

  *Prezzo unitario in configurazione base

• 

  Caricare gli anelli per la saldatura

  GANTER

  • Sconto volumi elevati

  A partire da∗ ：	58.72 €
  Consegna da ：	7 giorni

  *Prezzo unitario in configurazione base

Loading...